VPN setup on Windows 7
So I have a computer that everything I try to setup a VPN connection it keeps defaulting to dial-up settings. I click on connect to a workplace but when I finish the setup the VPN connection keeps trying to use dial-up.
I get a 797 error as well.
Any ideas?
August 30th, 2012 6:22pm
Hi,
Did you create an incoming VPN or outgoing VPN?
Please follow these steps to set incoming VPN and outgoing VPN on Windows 7:
Incoming VPN connection:
1.First go to Control Panel and open Network and Sharing Center.
2.Click on Change adapter settings.
3.Press
Alt+F and select New Incoming connection
4.Put a check on who youd like to give access to this computer or you can configure a new account by clicking on Add someone,after that click on Next.
5.Put a check mark on Through the Internet. Click on Next.
6.Select the protocols you want to enable for this connection. Click on Allow access.
7.Make a note of the Computer name as this will be used by the client to connect to this computer and after that Click on Close.
Outgoing VPN connection:
1.First go to Control Panel and open Network and Sharing Center.
2.Click on Set up a new connection or network.
3.Select Connect to a workplace then click on Next.
4.Select Use my internet connection (VPN).
5.Type the IP address or computer name where you wish to connect and your connection name under the Destination name field.
6.Enter a User name and password that has been granted access to the host computer.
7.For getting connected through created VPN connection, you can either right-click on the Network icon in the system tray and select Network and Sharing Center or go to Control Panel and open
Network and Sharing Center, and click on Connect to a network.
8.Now connect VPN Connection windows will appears.
And about error 797, it usually occur with dial up connection, please refer this KB:
http://support.microsoft.com/kb/317222
Hope that helps.
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
Free Windows Admin Tool Kit Click here and download it now
August 31st, 2012 2:55am
Hi,
Did you create an incoming VPN or outgoing VPN?
Please follow these steps to set incoming VPN and outgoing VPN on Windows 7:
Incoming VPN connection:
1.First go to Control Panel and open Network and Sharing Center.
2.Click on Change adapter settings.
3.Press
Alt+F and select New Incoming connection
4.Put a check on who youd like to give access to this computer or you can configure a new account by clicking on Add someone,after that click on Next.
5.Put a check mark on Through the Internet. Click on Next.
6.Select the protocols you want to enable for this connection. Click on Allow access.
7.Make a note of the Computer name as this will be used by the client to connect to this computer and after that Click on Close.
Outgoing VPN connection:
1.First go to Control Panel and open Network and Sharing Center.
2.Click on Set up a new connection or network.
3.Select Connect to a workplace then click on Next.
4.Select Use my internet connection (VPN).
5.Type the IP address or computer name where you wish to connect and your connection name under the Destination name field.
6.Enter a User name and password that has been granted access to the host computer.
7.For getting connected through created VPN connection, you can either right-click on the Network icon in the system tray and select Network and Sharing Center or go to Control Panel and open
Network and Sharing Center, and click on Connect to a network.
8.Now connect VPN Connection windows will appears.
And about error 797, it usually occur with dial up connection, please refer this KB:
http://support.microsoft.com/kb/317222
Hope that helps.
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
August 31st, 2012 3:00am
Hi,
Hows everything going? Please feel free to give me any update.
Thank you for your cooperation.
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
Free Windows Admin Tool Kit Click here and download it now
September 2nd, 2012 9:33pm
Hi,
Hows everything going? Please feel free to give me any update.
Thank you for your cooperation.
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
September 2nd, 2012 9:39pm
The steps you listed I've done countless times pre this post. The problem is that the network connections it creats keeps defaulting to dial-up. I can't get it to do anything else.
Free Windows Admin Tool Kit Click here and download it now
September 4th, 2012 6:03pm
The steps you listed I've done countless times pre this post. The problem is that the network connections it creats keeps defaulting to dial-up. I can't get it to do anything else.
September 4th, 2012 6:07pm
Hi,
Try to go to Control Panel->Network And Internet Connections->click Set Up Or Change Your Internet Connection->click Connection tab->click Never Dial A Connection->click Ok and
close the control panel.
Hope this helps
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
Free Windows Admin Tool Kit Click here and download it now
September 5th, 2012 1:56am
Hi,
Try to go to Control Panel->Network And Internet Connections->click Set Up Or Change Your Internet Connection->click Connection tab->click Never Dial A Connection->click Ok and
close the control panel.
Hope this helps
Regards,
Leo
Huang
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.Leo Huang
TechNet Community Support
September 5th, 2012 1:59am